BINGO

   home / products / autogas / BINGO

  Akme / BINGO / ECUs / Interfaces / Emulators / Accessories

   Lambda System BINGO-S

Bingo S BINGO-S lambda system is used for controlling and optimization of the gas-air mixture taken by the engine using the signal from the oxygen sensor. It protects the catalytic converter in the vehicle. Contains 4 or 6 channel petrol injectors emulator. Miniature control panel allows switching between petrol and gas. When connected to the tank level sensor it displays the current level with 5 led diodes.

In the complete set you will find: electronic control unit, main harness, emulator harness (with or without European connectors), actuator with Sonceboz stepper motor, miniature control panel, temperature sensor and small mounting elements.

BINGO-S is entirely programmed using PC computer or Simpad device.

The device is certified according to Regulation no. 67R01. Type-approval numbers you may find here.

The software and connection diagrams you may find in programs section.



  Lambda System BINGO-M

Bingo M
BINGO-M called by us “Small Bingo”, has been created for the needs of our customers, which asked for a device combining advantages of BINGO (production discontinued) and BINGO-S device. We created the device having improved microcontroller program taken from BINGO-S, in the small economical enclosure with built-in one channel injector emulator. Miniature control panel has led diodes indicating switching to gas and gas reserve.

In the complete set you will find: electronic control unit, harness, control panel and small mounting elements.

The software is very similar to BINGO-S with some additional options. The PC interface has not been changed.

The algorithms for stepper motor controlling are based on our experiences with BINGO-S and chassis dynamometer tests made in our premises. In this way we created the controller operating correctly in most vehicles and very price competitive.

The device is certified according to Regulation no. 67R01. Type-approval numbers you may find here.

The software and connection diagrams you may find in programs section.



   Basic parameters of BINGO-S and BINGO-M



  • Available versions:
  • BINGO-M: one channel emulator, without injector connectors, reserve indication,
  • BINGO-S.4: four channel emulator, without injector connectors, full level indication,
  • BINGO-S.4W: four channel emulator, with european injector connectors, full level indication,
  • BINGO-S.6: six channel emulator, without injector connectors, full level indication,
  • BINGO-S.6W: six channel emulator, with european injector connectors, full level indication.

    Basic settings:
  • Autoadaptation – device will start operating from the initial position and will be adapting to the current conditions.

    Oxygen sensor type:
  • 0..1V raising signal,
  • 0..5V raising signal,
  • 5..0V falling signal,
  • 0,8..1,6V raising signal.
  • Operatem with sensors type PULL-UP I PULL-DOWN (Bingo-S version).

    Throttle position sensor (TPS) type:
  • 0..5V linear signal,
  • > 5..0V linear signal,
  • no TPS,
  • 0-12V switch type (plus connection),
  • 12-0V switch type (ground connection),
  • BOSCH (two tracks).
  • TPS inertion on idle run (0,1-0,4) V (Bingo-S version).

    Oxygen sensor emulation:
  • ground (ground connection),
  • wave (simulation with the modifiable square wave – frequency, duty cycle),
  • disconnected (no signal).

    Driving type:
  • normal,
  • economical,
  • sport.

    Tank level sensor type:
  • 9 levels,
  • 0-90 ohm,
  • reserve.

    Engine speed:
  • choice of the ignition system type,
  • choice of the switching level (1500-3500 rpm),
  • switching with raising or falling rpm.

    Additional functions:
  • CUT-OFF function,
  • limit of maximum engine speed,
  • setting of the minimum temperature for switching to gas (10..60 °C)

    Advanced parameters:
  • maximum opening of the stepper motor – setting of the value from the range 20-255 steps with 1 step accuracy,
  • minimum opening of the stepper motor – setting of the value from the range 20-255 steps with 1 step accuracy,
  • time of emulation of the HIGH state – range 0,025-6,375 seconds, accuracy 0,025 seconds,
  • time of emulation of the LOW state – range 0,025-6,375 seconds, accuracy 0,025 seconds,
  • lambda readout delay (open loop delay) – range 0:05-21:15, accuracy 0:05 (minutes:seconds),
  • time of phase overlap gas/petrol – time of keeping the injector working (from opening gas valve to the distributing the gas through the mixer) – range 0,1-10,0) seconds, accuracy 0,1 seconds.

Infoline & technical support for foreign and mobile connections: 0048 422 999 139

*From Polish landline call 0801 563 563 or 0801 KME KME
KME Poland - Teresy 103a, PL-91-222 Lodz, tel. +48 (42) 6110026, fax +48 (42) 6118252, http://www.kme.com.pl
navi-> [HOME]=> About us: history, certificates, contact. Products: autogas, diagnostics, other. Documentation: software, manuals, presentations.